Singer W1750 Uživatelský manuál

/...; ^INSTRUCTION MANUAL FORSEWING MACHINEP P.its...' ' 0WHITE

REMOVING BOBBIN CASE AND BOBBIN1. Raise needle to its highest position and open the shuttle race cover.Hinged latch2. Open hinged latch of

INSERTING BOBBIN CASE INTO SHUTTLE RACE1. Raise needle to its highest position, pulling thread to the front, open the latch of bobbin c

THREADING UPPER THREADThreading the thread from A to I as shownTwin needle threading

DRAWING UP BOBBIN THREADHold upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and comes

CONTROL DIALPattern selector dial Thread tension dial Zig-zag width dial Stitch length dial Reverse button11

ADJUSTING THREAD TENSIONCorrectWeakStrongUpper thread tension may be adjusted by turning the thread tension dial.FabricUpper threadBobbin threadIncorr

REGULATING THE PRESSER FOOT PRESSURE3.Push down inner pin (A) to increase pressure, (Light to medium fabrics)Push down outer ring to relea

CHANGING NEEDLE1. Raise needle to its highest position.2. Loosen neeaie clamp screw and remove old needle.3. With the flat side of the needle facin

FABRIC THREAD • NEEDLE TABLEPlease note that the following list is a guide when sewing different fabrics.15

SEWING (PATTERN SELECTOR) AND OPERATION TABLEOt.: 7.'- i iu '.VayPatternStitch lengthPn,‘SSt>r foritDrop feed1St'aight stitch11%=>

POLARIZED PLUGS CAUTIONThis product is equipped with a poiarized aiternating current iine piug (a piug having one biade wider than the other). Thi

TO START SEWINGImportant Hints.1.3.4.5.Raise the take-up lever to its highest position when starting and stopping sewing.Hold both thread

TO FINISH SEAM1. Sew to the edge of seam.2. Push the reverse button and sew m reverse for about 3--4 cms.3. Raise needle to its highest position,4.

STRAIGHT STITCH1, This type of stitching is the one used most frequently.2 The zig-zag presser foot can be used for both straight and zig-zag sewing.

OVERCASTING1/r/Use these stitches for oversewing rough edges.STRAIGHT STRETCH STITCHUse this stitch with knitted, tricot or other stretchy

BLIND STITCH1. Fold fabric as shown.1 //2. To finish seam as shown.//121

Adjust width and needle position to obtain correct seam.Needle is not piercing edge of fold at all.X<'Needle is pierces edge of fold too

BUTTON SEWING(Use darning plate see page 11)1. Lower drop feed.2. Use button presser foot and attach firmly.3. Place button between presser foot an

ZIPPER SEWINGSelect straight stitch.1. Fold the fabric about 2cm and place fabric under foot.2. Zipper foot is designed to sew close to a rai

BUTTON HOLE SEWINGSelect stitch length dial in area indicated.Pattern selector dialStepsSettings1. Set dial to "1" position.2. Sew left si

HEMMING1. Raise the foot and the needle to its highest position. Replace the foot with the hemmer foot.2. Fold over the fabric edg

CONTENTSName of Parts... 1 &

TWIN NEEDLE (optional).. .0, no,™, »w™ p.»n, Po,P ,p,e.ds ,P.ou,P .P. san,S,rs::;n, wid,P .podld „o. a«ce.d ,d. <ddd wide. .1.* wid.d, e.c.edin, .d

QUILTER1, Insert supporter of quilter,2. Move quilter and adjust stitch distance.SEAM GUIDEdistance from edge of material.2, Set guide in hole on be

NAME OF PARTS (FRONT VIEW)@—c:1 Pattern selector dial2 Pressure regulator3 Take up lever4 Thread tension dial5 Presser foot6 Shuttle cover7 Extens

(REAR VIEW)Bobbin winder spindleBobbin winder stopperUpper thread guideStop Motion knob Hand wheel

ACCESSORIESOBobbinFeltZigzag foot (On machine)Button footMachine OilZipper footButton hole cutter Screw driveroNeedle#14

BEFORE SEWING1. Fit the machine plug into the machine.2. Plug the machine to the power supply.3. Sewing speed can be varied by the speed controller

REMOVING EXTENSION TABLE1. Hold the left end of table and pull out in direction of arrow.FREE-ARM SEWING1. Especially useful when sewing sl

WINDING THE BOBBIN1. Release stop motion knob.2. Thread as shown.3. When bobbin is filled, tighten stop motion knob.5cm thread